Service Infiniti QX4 since 1996 of release
1. Introduction
2. The maintenance instruction
3. Routine maintenance
4. The engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. A transmissionnaja line
9. Brake system
9.1. Specifications
9.2. System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
9.3. Check of a condition and replacement of brake lines and hoses
9.4. Replacement колодок disk brake mechanisms of forward wheels
9.5. Removal and installation of a support of the disk brake mechanism
9.6. Removal and installation of a brake disk
9.7. Replacement of brake boots of drum-type brake mechanisms of back wheels
9.8. Removal and installation of the main brake cylinder (ГТЦ)
9.9. Removal and installation of assemblage of the vacuum amplifier of brakes
9.10. Prorolling of brake system
9.11. Adjustment of a drive of a lay brake
9.12. Adjustments of a pedal of a foot brake
9.13. Adjustment of a spring of the valve-regulator sensitive to loading (LSV)
9.14. Adjustment of gauges-switches of stoplights and темпостата
9.15. Removal and hydromodulator ABS installation
9.16. Removal and G-gauge installation
9.17. Check of serviceability of functioning of wheel gauges ABS
9.18. Check of serviceability of functioning of the G-gauge
9.19. Check of serviceability of functioning of the relay приводного the hydromodulator electromotor
9.20. Check of serviceability of functioning of the relay of the electromagnetic valve of hydraulic modulator ABS
10. A suspension bracket and a steering
11. A body
12. An electric equipment
 






Знакомства в Перми посмотреть.
тюнинг киев, интерьер.






9-7-zamena-tormoznykh-bashmakov-barabannykh-tormoznykh-mekhanizmov-zadnikh-koles.html

9.7. Replacement of brake boots of drum-type brake mechanisms of back wheels


Design of drum-type brake mechanisms of back wheels

1 — Ankernyj a finger
2 — Zaglushka
3 — the Brake board
4 — the Control stopper
5 — the Spring
6 — the Forward brake boot
7 — the prorolling Gate
8 — the Spring of pistons
9 — a piston Cup
10 — the Piston
11 — Pylnik
12 — the Lock ring
13 — the Executive lever
14 — the Wavy washer

15 — the Back boot
16 — Adjusting разжимная a lath
17 — Pylnik
18 — the Piston
19 — a piston Cup
20 — the Wheel cylinder
21 — the regulator Lever
22 — a spring Saddle
23 — the Directing spring
24 — the Holder of a spring
25 — a regulator Spring
26 — the Top coupling spring
27 — the Bottom coupling spring


Removal

 PERFORMANCE ORDER

  1. Prop up forward wheels of the car противооткатными boots. Release a lay brake. Поддомкратьте a back of the car also establish it on props (the Scheme of an institution of props for car fixing in the lifted position see an illustration). Remove a corresponding back wheel.
  2. Remove a brake drum, — if the drum does not act in film even after regulator assignment, screw in its apertures pair of bolts and start gradually from to tighten, wringing out a drum from a brake board.
  3. Remove coupling and directing springs of brake boots.
  4. Remove boots in gathering with a regulator.
  5. Separate a regulator.
  6. In case of need remove the remained components.


Installation

 PERFORMANCE ORDER

  1. Installation is made in an order, the return to an order of dismantle of components, — do not forget to grease preliminary acting parts of a brake board, a carving of a regulator and a finger of the executive lever of a drive of a lay brake with special brake greasing.
  2. Manually check up freedom of rotation of a drum.


On page back
9.6. Removal and installation of a brake disk
On the following page
9.8. Removal and installation of the main brake cylinder (ГТЦ)