Service Infiniti QX4 since 1996 of release
1. Introduction
2. The maintenance instruction
3. Routine maintenance
4. The engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. A transmissionnaja line
9. Brake system
9.1. Specifications
9.2. System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
9.3. Check of a condition and replacement of brake lines and hoses
9.4. Replacement колодок disk brake mechanisms of forward wheels
9.5. Removal and installation of a support of the disk brake mechanism
9.6. Removal and installation of a brake disk
9.7. Replacement of brake boots of drum-type brake mechanisms of back wheels
9.8. Removal and installation of the main brake cylinder (ГТЦ)
9.9. Removal and installation of assemblage of the vacuum amplifier of brakes
9.10. Prorolling of brake system
9.11. Adjustment of a drive of a lay brake
9.12. Adjustments of a pedal of a foot brake
9.13. Adjustment of a spring of the valve-regulator sensitive to loading (LSV)
9.14. Adjustment of gauges-switches of stoplights and темпостата
9.15. Removal and hydromodulator ABS installation
9.16. Removal and G-gauge installation
9.17. Check of serviceability of functioning of wheel gauges ABS
9.18. Check of serviceability of functioning of the G-gauge
9.19. Check of serviceability of functioning of the relay приводного the hydromodulator electromotor
9.20. Check of serviceability of functioning of the relay of the electromagnetic valve of hydraulic modulator ABS
10. A suspension bracket and a steering
11. A body
12. An electric equipment
 






Свежие новости: алиэкспресс на русском в рублях





9-12-regulirovki-pedali-nozhnogo-tormoza.html

9.12. Adjustments of a pedal of a foot brake


Adjusting parametres of a pedal of a foot brake

And — Size of a free wheeling of a pedal
D — Height of position of the squeezed out pedal
Н — Height of position of the released pedal

With 1 — the Backlash of the gauge-switch of stoplights
With 2 — a gauge-switch Backlash темпостата


Pedal free wheeling

The size of a free wheeling of a pedal of a foot brake "And" (Adjusting parametres of a pedal of a foot brake see an illustration) should make 4—12 mm.

 PERFORMANCE ORDER

  1. In case of need release a counternut and make necessary adjustment by rotation of a rod of a pusher of the vacuum amplifier of brakes around a cutting finger. Having achieved demanded result, tighten a counternut with demanded effort (12—15 Nanometers). Check up serviceability of switching-off of stoplights at release pedals.


Reserve course of a pedal

 PERFORMANCE ORDER

  1. At the started engine ask the assistant to squeeze out a pedal with effort of an order 49 кГс and measure position height колодки the squeezed out pedal from a floor, — do not forget to unbend a floor-mat. At negative results of check drive away the car in a workshop of car-care centre for performance of corresponding adjustment.

Excessive lowering of a pedal can speak infringement of adjustment of drum-type brake mechanisms of back wheels, — try to cock and release a lay brake some times.


Height of position of a pedal

 PERFORMANCE ORDER

  1. Measure height of position lowered () and squeezed out (D) pedals of a lay brake (Adjusting parametres of a pedal of a foot brake see an illustration). Compare results of measurement to requirements of Specifications. In case of need release a counternut and make necessary adjustment by rotation of a rod of a pusher of the brake amplifier. Having finished, tighten a nut with demanded effort (16—22 Nanometers), — track, that the rod tip remained in a cutting finger of a pusher.


On page back
9.11. Adjustment of a drive of a lay brake
On the following page
9.13. Adjustment of a spring of the valve-regulator sensitive to loading (LSV)