2.5.10. Instructions for use a control system of the speed (темпостатом)
At refusals темпостата (ASCD) there is an automatic switching-off of the system, an accompanied blinking of a control lamp темпостата on an instrument guard of the car (the car Equipment, an arrangement of devices and controls see).
If the control lamp темпостата starts to blink, make deenergizing of system from the main switch and drive away the car on a car repair shop.
In a blinking of a control lamp can result inclusion темпостата from the main switch at simultaneous нажимании on buttons of management of system RES/ACCEL, COAST/SET or CANCEL control panels on a steering wheel, system activation should be made according to the instructions resulted more low.
It is not necessary to use темпостат in following road conditions:
- When there is no possibility of movement with the chosen constant speed;
- At movement on the loaded roads;
- At movement on a streamer;
- In hilly and mountain districts;
- At a slippery road covering;
- At a strong wind.
Infringement of the given prevention is fraught with control loss over management!
Management of functioning темпостата
Management of functioning темпостата
The control system of speed (темпостат) provides possibility of automatic maintenance of speed of movement of the car in a range from 48 to 144 km/h without use of a pedal of gas.
For overtaking fulfilment squeeze out a gas pedal. After the pedal will be released, the car will return to chosen before cruiser speed.
At movement under a bias or uphill темпостат does not provide maintenance of cruiser speed of movement of the car and should be switched off.
Cancellation of the chosen cruiser speed can be made in three various ways:
- Press button CANCEL (Cancellation), — the control lamp темпостата should go out;
- Slightly squeeze out a pedal of a foot brake, — the control lamp темпостата should go out;
- Take advantage of the main switch темпостата, — should go out a control lamp темпостата, and also built in a switch key a control lamp.
After squeezing of a pedal of a foot brake at simultaneously pressed button RES/ACCEL on the control panel, it is necessary to disconnect темпостат the main switch and to activate it repeatedly after a set of demanded speed of movement.
Темпостат it is disconnected automatically at decrease in speed of movement of the car more than on 13 km/h below the chosen cruiser value.
Deenergizing of a control system by speed can be made also by squeezing of a pedal of coupling (model with Manual transmission) or movings of the lever of the selector to position «N» (models with АТ), — the control lamp темпостата on an instrument guard should go out.
Increase of the chosen cruiser speed of movement of the car can be made in three ways:
- Squeeze out an accelerator pedal when the car will be dispersed till demanded speed press and release button COAST/SET on the control panel (Management of functioning темпостата see an illustration);
- Press and keep pressed button RES/ACCEL control panels functioning темпостата (Management of functioning темпостата see an illustration), — when the car will be dispersed till demanded speed, release the button;
- Short-term pressing button RES/ACCEL it is possible to make step acceleration of the car with step of 1.6 km/h.
For fall of cruiser speed:
- Slightly press a pedal of a foot brake, — when speed of movement of the car will decrease to demanded value, press button COAST/SET;
- Press button COAST/SET and keep its pressed until the car will not be braked till demanded speed;
- Short-term pressing button COAST/SET it is possible to make step decrease in value of cruiser speed of the car with step of 1.6 km/h.
For return to earlier chosen cruiser speed quickly press button RES (Management of functioning темпостата see an illustration), — as soon as the car will be dispersed over 48 km/h, темпостат will automatically finish it to chosen before cruiser speed of movement which will support further.
Adjustment of a cable of a drive throttle заслонки темпостата
Adjustment of a cable of a drive темпостата
Try not to suppose перекручивания приводного cable ASCD!
At adjustment on pull a cable with excessive effort!
- Release lock and adjusting nuts (Adjustment of a cable of a drive темпостата see an illustration).
- Check up correctness of adjustment of a cable of gas.
- Tighten an adjusting nut so that the throttle drum has started to move.
- Release a nut on 0.5—1 turns and strongly tighten a counternut.