Service Infiniti QX4 since 1996 of release
1. Introduction
2. The maintenance instruction
3. Routine maintenance
4. The engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. A transmissionnaja line
9. Brake system
10. A suspension bracket and a steering
10.1. Specifications
10.2. An estimation of the general condition of components of a suspension bracket and a car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering draughts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Pretightness adjustment ступичных bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblages of a forward suspension bracket
10.8. Removal and installation ступичной assemblage and a rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement ступичных bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assemblage of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Prorolling of a hydraulic path of a steering drive
10.19. Checks and steering wheel adjustments
10.20. Check of effort of resistance to sliding рейки the steering mechanism
10.21. Twisting moment adjustment проворачивания a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure ГУР
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation редукторной assemblages
10.25. Removal and installation of assemblage of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and steering wheel installation
10.28. Removal and installation of assemblage combined подрулевых switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. A body
12. An electric equipment
 












10-8-snyatie-i-ustanovka-stupichnojj-sborki-i-povorotnogo-kulaka.html

10.8. Removal and installation ступичной assemblage and a rotary fist


Design ступичной assemblages of a forward wheel


Removal

 PERFORMANCE ORDER

  1. Поддомкратьте the car also establish it on props (the Scheme of an institution of props for car fixing in the lifted position see an illustration). Remove a corresponding forward wheel.
  2. Disconnect electroconducting from wheel gauge ABS.
  3. Turn out fixing bolts, remove a support and tie up its wire to suspension bracket elements (the Suspension bracket and a steering see the Head).
  4. Turn out fixing bolts and remove приводной a flange.
  5. Lungs постукиваниями a hammer with brass brisk liberate from a nave a pin of an external SHRUS of a power shaft.
  6. Remove a lock washer.
  7. Having taken advantage of special stripper KV40105400, turn away a nut Hubs the bearing.
  8. Remove the external bearing and hub assemblage.
  9. Give fastening bolts to a nave of a rotary fist.
  10. Remove шплинт a tip of steering draught and give шпилечную a nut.
  11. By means of stripper ST9020001 separate a draught tip.


Installation

 PERFORMANCE ORDER

  1. Installation is made in an order, the return to an order of dismantle of components. Do not forget to adjust properly ступичные bearings (pretightness Adjustment ступичных bearings of forward wheels see). Track, that were it is replaced all lock washers and sealing elements. All fixture tighten with demanded effort.


On page back
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblages of a forward suspension bracket
On the following page
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability