Service Infiniti QX4 since 1996 of release
1. Introduction
2. The maintenance instruction
3. Routine maintenance
4. The engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. A transmissionnaja line
9. Brake system
10. A suspension bracket and a steering
10.1. Specifications
10.2. An estimation of the general condition of components of a suspension bracket and a car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering draughts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Pretightness adjustment ступичных bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblages of a forward suspension bracket
10.8. Removal and installation ступичной assemblage and a rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement ступичных bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assemblage of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Prorolling of a hydraulic path of a steering drive
10.19. Checks and steering wheel adjustments
10.20. Check of effort of resistance to sliding рейки the steering mechanism
10.21. Twisting moment adjustment проворачивания a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure ГУР
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation редукторной assemblages
10.25. Removal and installation of assemblage of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and steering wheel installation
10.28. Removal and installation of assemblage combined подрулевых switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. A body
12. An electric equipment
 












10-27-snyatie-i-ustanovka-rulevogo-kolesa.html

10.27. Removal and steering wheel installation

Cars considered in the present Management are equipped by system of the additional safety SRS more known as a pillow of safety. Before to perform any works near to assemblage of a pillow or a steering column, without fail disconnect system in order to avoid reception of traumas as a result of its casual operation (the Electric equipment see the Head). Isolation and contact sockets of electroconducting of chain SRS are painted in bright yellow colour. It is not necessary to connect any diagnostic devices to the given chain!


Removal

Bolts of fastening of the module of a pillow of safety are planted on special hermetic and to a reuse are not subject.


 PERFORMANCE ORDER

  1. Before to start steering wheel removal, деактивируйте SRS (the Electric equipment see the Head).
  2. Remove the bottom cover of a casing of a steering column.
  3. Disconnect electroconducting from the module of a driver's face-to-face pillow of safety, then remove the left and right sections of a casing.
  1. By means of a key of type TORX turn out bolts of fastening of the module (the prevention see).
  1. Remove a pillow of safety and a spiral cable drum. Transfer assemblage on a workbench and lay its overlay upwards.
  2. Result forward wheels of the car in rectilinear position.
  3. Disconnect horn electroconducting, and also all other electroconducting, disturbing to steering wheel removal.
  4. Give a nut of fastening of a steering wheel, remove a washer and mark position of a wheel concerning a shaft of a steering column.
  1. By means of a special stripper remove a steering wheel and disconnect a cable of a drive of blocking of switching АТ.

Do not draw a stripper bolt! Do not make attempts of knocking down of a steering wheel by means of a hammer!


Installation

 PERFORMANCE ORDER

  1. Make sure that forward wheels still are in rectilinear position.
  2. Check up correctness of combination of a uvula of the gauge-switch of the returnable device of the switch of indexes of turn with reciprocal риской подрулевого the switch.
  1. Make sure that spiral cable drum SRS is in neutral (central) position, and adjusting labels are combined in the correct image.

At wrong installation the cable drum can appear jammed at strong deployment of a steering wheel!

  1. Establish a drum on a steering column. In case of need make drum centering for what turn it on 2.5 turns from extreme position and achieve combination of adjusting labels. For reliability temporarily fix a drum in neutral position by means of an adhesive tape.
  1. Connect to a cable drum electroconducting.
  2. Connect a cable of blocking of switching АТ.
  3. Establish a casing of a steering column and remove fixing cable drum an adhesive tape.
  4. Establish a steering wheel, — track correctness of hit of a directing pin of a cable drum in reciprocal nests.
  5. Pass a cable drum in a wheel nave.
  6. Connect horn electroconducting, then enter a cable drum into gearing with ratchet doggies of a steering wheel.
  7. Tighten with demanded effort a nut of fastening of a steering wheel.
  8. Establish into place the module of a pillow of safety, screw NEW fixing bolts and tighten them with demanded effort.
  9. Establish into place remained elements of a casing of a steering column.
  10. In summary make activation SRS (the Electric equipment see the Head).


On page back
10.26. Removal and installation of the steering pump
On the following page
10.28. Removal and installation of assemblage combined подрулевых switches